Kraken and elven treeIl kraken e l'albero degli elfi

A cloud of points fills the space that a form should occupy, and branches grow towards them step by step, each point pulling the nearest branch and vanishing once it is reached: this is the space colonization algorithm of Runions, Lane and Prusinkiewicz (2007), in which the shape of a tree comes from the volume of its crown rather than from rules of branching. Here the volume is the crown of an elven tree around its tree house, or a shell around a ship that the tentacles of a kraken climb out of the sea to seize.

Una nuvola di punti riempie lo spazio che una forma deve occupare, e i rami crescono verso di essi passo dopo passo, ogni punto attira il ramo più vicino e sparisce quando è raggiunto: è l'algoritmo di colonizzazione dello spazio di Runions, Lane e Prusinkiewicz (2007), in cui la forma di un albero viene dal volume della sua chioma più che da regole di ramificazione. Qui il volume è la chioma di un albero degli elfi attorno alla sua casa sull'albero, oppure un guscio attorno a una nave che i tentacoli di un kraken risalgono dal mare per afferrare.

The form that is printed (the branches as tubes; the print is their union, meshed finer); drag to turn, use the wheel or pinch to zoom.La forma che si stampa (i rami come tubi; la stampa è la loro unione, con una mesh più fine); trascina per ruotare, usa la rotella o il pizzico per lo zoom.

Points that pull, branches that growPunti che attirano, rami che crescono

At each step every attraction point that is still there finds the nearest node of the structure within the radius of influence di; a node v pulled by the set S(v) grows a new node at v + D n, with n the normalized sum of the unit vectors (s − v)/|s − v| for s in S(v) plus an upward bias, and the points within the kill distance dk of a new node are removed (in the side view, gold for the points left and grey for those reached). Since a node may be pulled again in later steps by other points, the structure branches by itself wherever the points split into groups; a large di gives straight, sparse branches and a small one tortuous, dense branches, as Runions et al. remark. The tentacles of the kraken grow only at their tips, so that each stays one curve, and a tentacle that no point pulls goes on along its direction, bending towards the ship.

A ogni passo ogni punto di attrazione ancora presente trova il nodo della struttura più vicino entro il raggio d'influenza di; un nodo v attirato dall'insieme S(v) fa crescere un nuovo nodo in v + D n, con n la somma normalizzata dei versori (s − v)/|s − v| per s in S(v) più una spinta verso l'alto, e i punti entro la distanza di cattura dk di un nuovo nodo sono tolti (nella vista di fianco, oro i punti rimasti e grigio quelli raggiunti). Poiché un nodo può essere attirato di nuovo nei passi seguenti da altri punti, la struttura si ramifica da sé dove i punti si dividono in gruppi; un di grande dà rami dritti e radi, uno piccolo rami tortuosi e fitti, come osservano Runions et al. I tentacoli del kraken crescono solo in punta, così ognuno resta una sola curva, e un tentacolo che nessun punto attira prosegue nella sua direzione piegando verso la nave.

The radii follow the pipe model: a tip has the thinnest printable radius, and at a fork rγ equals the sum of the rγ of the children, with γ = 2 for the rule that Leonardo wrote in his notebooks (the cross sections of the branches add up to that of the trunk) and γ = 3 for Murray's law of blood vessels; the tentacles taper instead from 3.2 mm to the thinnest radius. The points are denser upwards and no branch grows downwards, so that most of the structure rises (for the kraken the upward bias is weaker, so that the tentacles can wind round the hull).

I raggi seguono il modello dei tubi: una punta ha il raggio stampabile più sottile, e a una biforcazione rγ è la somma degli rγ dei figli, con γ = 2 per la regola che Leonardo scrisse nei suoi taccuini (le sezioni dei rami sommano a quella del tronco) e γ = 3 per la legge di Murray dei vasi sanguigni; i tentacoli invece si assottigliano da 3.2 mm al raggio più sottile. I punti sono più fitti in alto e nessun ramo cresce verso il basso, così la maggior parte della struttura sale (per il kraken la spinta verso l'alto è più debole, così i tentacoli possono avvolgersi attorno allo scafo).

Download for 3D printingScarica per la stampa 3D

A 3D print of this formUna stampa 3D di questa forma

The tree or the kraken can be ordered as a 3D print, grown from the points chosen above. The request sends the link to the form as it is on the screen.

Puoi ordinare l'albero o il kraken come stampa 3D, cresciuti dai punti scelti sopra. La richiesta manda il link alla forma così com'è sullo schermo.

One closed body: the union of the branches as round cones with the base (a disc under the tree, the sea under the ship), the platform and the hut, or the hull, the mast, the sail and the head of the kraken. What needs supports: the branches flatter than 45 degrees (their share of the length is given above the text: with the default settings about three fifths of the tree and more of the kraken, since a crown spreads sideways and a tentacle arches over the ship), the lower side of a tentacle where it curls round the hull, and the eaves of the roof of the hut; the platform rests on a cone at 45 degrees, the hull sits on the water and the sail is a vertical triangle, so these print without them. Tree supports in the slicer, touching the model only on the branches, work best, and a larger upward bias reduces them; the thinnest branch is a radius in millimetres of the print, whatever the size.

Un solo corpo chiuso: l'unione dei rami come coni arrotondati con la base (un disco sotto l'albero, il mare sotto la nave), la piattaforma e la capanna, oppure lo scafo, l'albero maestro, la vela e la testa del kraken. Cosa richiede supporti: i rami più piatti di 45 gradi (la loro quota della lunghezza è data sopra il testo: con le impostazioni predefinite circa tre quinti dell'albero e di più del kraken, perché una chioma si allarga di lato e un tentacolo si inarca sopra la nave), il lato inferiore di un tentacolo dove si avvolge attorno allo scafo, e la gronda del tetto della capanna; la piattaforma poggia su un cono a 45 gradi, lo scafo sta sull'acqua e la vela è un triangolo verticale, quindi questi si stampano senza. I supporti ad albero dello slicer, che toccano il modello solo sui rami, sono i più adatti, e una spinta verso l'alto più forte li riduce; il ramo più sottile è un raggio in millimetri della stampa, qualunque sia la dimensione.