RadiolariansRadiolari

Radiolarians are single-celled plankton of the open sea that build a skeleton of opaline silica, often a sphere pierced by pores, or two or three spheres one inside the other, joined by radial beams that go on outside as spines. Ernst Haeckel described some thousands of species from the samples of the Challenger expedition (Report on the Radiolaria, 1887) and drew the most striking of them in the plates of Kunstformen der Natur (1899–1904). Here the lattice of a sphere is the spherical Voronoi diagram of a set of seeds: each pore is the part of the sphere closer to its seed than to any other, the bars run along the borders, and three of them meet at every node. The seeds are spread by the golden angle (the Fibonacci sphere, which Lloyd's relaxation makes more even by moving each seed to the center of its cell) or placed on the vertices of a subdivided icosahedron.

I radiolari sono organismi unicellulari del plancton di mare aperto che costruiscono uno scheletro di silice opalina, spesso una sfera traforata da pori, o due o tre sfere una dentro l'altra, unite da travi radiali che proseguono all'esterno come spine. Ernst Haeckel ne descrisse alcune migliaia di specie dai campioni della spedizione del Challenger (Report on the Radiolaria, 1887) e disegnò le più notevoli nelle tavole di Kunstformen der Natur (1899–1904). Qui il reticolo di una sfera è il diagramma di Voronoi sferico di un insieme di semi: ogni poro è la parte della sfera più vicina al suo seme che a ogni altro, le barre corrono lungo i confini, e in ogni nodo se ne incontrano tre. I semi sono distribuiti per l'angolo aureo (la sfera di Fibonacci, che il rilassamento di Lloyd rende più uniforme spostando ogni seme al centro della sua cella) o posti sui vertici di un icosaedro suddiviso.

seedssemi \(z_i = 1 - \frac{2i+1}{n}\), \(\vartheta_i = i \cdot 137.5^\circ\); Euler \(V - E + F = 2\), three bars at a nodetre barre per nodo \(\Rightarrow \sum_k (6-k)\,N_k = 12\)

The skeleton of the numbers above: the same solid that is printed, traced on a coarser grid, first roughly and then finer; the inner shells are tinted gold. The spine length and the thorns are measured in radii of the outer shell, the bar width as a fraction of the mean side of a cell. Drag to turn, wheel or pinch to zoom.Lo scheletro dei numeri qui sopra: lo stesso solido della stampa, tracciato su una griglia più rada, prima grossolana e poi più fine; i gusci interni sono tinti d'oro. La lunghezza delle spine e gli aculei sono misurati in raggi del guscio esterno, lo spessore delle barre come frazione del lato medio di una cella. Trascina per ruotare, rotella o pizzico per lo zoom.
The net of the outer shell in Lambert's azimuthal equal-area projection, one hemisphere per disc (the south seen from below), each cell colored by its number of sides.La rete del guscio esterno nella proiezione azimutale equivalente di Lambert, un emisfero per disco (il sud visto da sotto), ogni cella colorata secondo il numero dei suoi lati.
cellscelle
5 · 6 · 7 · other5 · 6 · 7 · altre
· · ·
V − E + F
Σ (6 − k) Nk

Euler's formula forbids a sphere covered by hexagons alone. With three bars at every node, \(3V = 2E\) and \(\sum_k k N_k = 2E\), so that \(V - E + F = 2\) becomes \(\sum_k (6-k) N_k = 12\): the hexagons count zero and may be as many as one likes, but the pentagons must outnumber the heptagons by twelve. D'Arcy Thompson made this remark in On Growth and Form (1917) about Haeckel's Aulonia hexagona, whose net looks at first sight as if made of hexagons only. The icosahedral net has its twelve pentagons at the vertices of an icosahedron; the Fibonacci sphere has more, each paired with a heptagon, and the relaxation removes some of the pairs.La formula di Eulero vieta una sfera coperta di soli esagoni. Con tre barre in ogni nodo, \(3V = 2E\) e \(\sum_k k N_k = 2E\), sicché \(V - E + F = 2\) diventa \(\sum_k (6-k) N_k = 12\): gli esagoni contano zero e possono essere quanti si vuole, ma i pentagoni devono superare gli ettagoni di dodici. D'Arcy Thompson fece questa osservazione in On Growth and Form (1917) a proposito dell'Aulonia hexagona di Haeckel, la cui rete sembra a prima vista fatta di soli esagoni. La rete icosaedrica ha i suoi dodici pentagoni nei vertici di un icosaedro; la sfera di Fibonacci ne ha di più, ognuno in coppia con un ettagono, e il rilassamento toglie alcune delle coppie.

Download for 3D printingScarica per la stampa 3D

A 3D print of this skeletonUna stampa 3D di questo scheletro

The skeleton of the numbers above can be ordered as a 3D print, as one solid whose largest side is the size; with the stand, a column under the south pole rises from a disc, and the spines that reach below it are cut flat, where they become pillars. The lower half of a lattice sphere overhangs, so that the print is made with supports, which reach the inner shells through the pores. The request sends the link to the skeleton as it is on the screen.

Lo scheletro dei numeri qui sopra si può ordinare come stampa 3D, come un solo solido il cui lato maggiore è la dimensione; con il piedistallo, una colonna sotto il polo sud sale da un disco, e le spine che arrivano più in basso sono tagliate in piano, dove diventano pilastri. La metà inferiore di una sfera a reticolo è a sbalzo, sicché la stampa si fa con supporti, che raggiungono i gusci interni attraverso i pori. La richiesta manda il link allo scheletro così com'è sullo schermo.

The skeleton as one closed solid, its largest side equal to the size; with the stand, a column under the south pole rises from a disc about 2 mm thick, and the spines that reach below the bed are cut flat on it, where they become pillars. A lattice sphere does not print without supports, since its lower half overhangs: the slicer needs tree supports, which reach the inner shells through the pores, and with nested shells a resin printer gives the cleanest result. The status line gives the thickness of the bars: for a filament printer it should stay above about 1 mm (widen the bars, lower the number of cells or raise the size otherwise).

Lo scheletro come un solo solido chiuso, il lato maggiore pari alla dimensione; con il piedistallo, una colonna sotto il polo sud sale da un disco spesso circa 2 mm, e le spine che arrivano sotto il piano sono tagliate in piano, dove diventano pilastri. Una sfera a reticolo non si stampa senza supporti, poiché la sua metà inferiore è a sbalzo: lo slicer deve mettere supporti ad albero, che raggiungono i gusci interni attraverso i pori, e con gusci annidati una stampante a resina dà il risultato più pulito. La riga di stato dà lo spessore delle barre: per una stampante a filamento conviene restare sopra 1 mm circa (altrimenti allarga le barre, riduci il numero di celle o aumenta la dimensione).