Shells from three numbersConchiglie da tre numeri
A shell grows only at its margin, adding material to the aperture
without remaking what is already built, so that its form is that of a curve, the aperture,
swept along a spiral while it is enlarged at a constant rate. Raup (1966) showed that three
numbers describe most coiled shells: the expansion \(W\) of the whorl per revolution, the
distance \(D\) of the generating curve from the coiling axis (the ratio of its inner to its outer
edge, so that \(D = 0\) puts the inner edge on the axis and larger values open the coil, as in a
horn) and the translation \(T\) along the axis per revolution, relative to the distance of the
center of the curve from the axis. With \(T = 0\) the shell is planispiral, as in a nautilus or an
ammonite; with \(T > 0\) it rises into a spire, as in a snail or a turritella; with \(W\) of the
order of \(10^2\) to \(10^3\) less than one revolution makes a cap, which is the valve of a
bivalve.
Una conchiglia cresce solo sul margine, aggiungendo materiale
all'apertura senza rifare quello che è già costruito, sicché la sua forma è quella di una curva,
l'apertura, trascinata lungo una spirale mentre si ingrandisce a ritmo costante. Raup (1966) ha
mostrato che tre numeri descrivono gran parte delle conchiglie avvolte: l'espansione \(W\) del giro
per rivoluzione, la distanza \(D\) della curva generatrice dall'asse di avvolgimento (il rapporto
fra il suo bordo interno e quello esterno, sicché \(D = 0\) mette il bordo interno sull'asse e
valori più grandi aprono la spira, come in un corno) e la traslazione \(T\) lungo l'asse per
rivoluzione, relativa alla distanza del centro della curva dall'asse. Con \(T = 0\) la conchiglia è
planispirale, come nel nautilus o in un'ammonite; con \(T > 0\) si alza in una spira, come in una
chiocciola o in una turritella; con \(W\) dell'ordine di \(10^2\) o \(10^3\) basta meno di una
rivoluzione per fare una cupola, che è la valva di un bivalve.
\(r(\theta) = r_0\, W^{\theta/2\pi}\), \(z(\theta) = -T\, r(\theta)\), \(r_0 = a\,(1+D)/(1-D)\), apertureapertura \(a\,W^{\theta/2\pi}(\cos\varphi,\ S \sin\varphi)\)
Download for 3D printingScarica per la stampa 3D
A 3D print of this shellUna stampa 3D di questa conchiglia
The shell of the numbers above can be ordered as a 3D print: its
wall, of the thickness chosen, around the cavity, from the apex to the last aperture, which stays
open. A shell lying wholly on one side of its last aperture, as the valve of a bivalve, is laid on
that aperture; any other stands on its coiling axis, apex up, on a disc. The request sends the
link to the shell as it is on the screen.
Puoi ordinare la conchiglia dei numeri qui sopra
come stampa 3D: la sua parete, dello spessore scelto, attorno alla cavità, dall'apice all'ultima
apertura, che resta aperta. Una conchiglia che sta tutta da una parte della sua ultima apertura,
come la valva di un bivalve, è posata su quell'apertura; ogni altra sta sull'asse di
avvolgimento, con l'apice in alto, su un disco. La richiesta manda il link alla conchiglia così
com'è sullo schermo.
The shell of the numbers above as a solid to print: its wall, of the
thickness asked for, around the cavity, from the apex to the last aperture, which stays open. The
solid is traced on a grid of cells (about 1/120 of the size, or 1/190 when fine) and is closed,
every edge between two triangles and every face turned outward, also where the whorls run into
one another; near the apex, where the whorl is thinner than the wall, it is solid, and what is
smaller than a cell is left out. A shell lying wholly on one side of its last aperture, as the
valve of a bivalve, is laid on that aperture; any other stands on its coiling axis, apex up, and
the stand is a disc into which its lowest part is sunk. STL has no unit (slicers read
millimeters), 3MF states millimeters.
La conchiglia dei numeri qui sopra come solido da stampare:
la sua parete, dello spessore scelto, attorno alla cavità, dall'apice all'ultima apertura, che
resta aperta. Il solido è tracciato su una griglia di celle (circa 1/120 della dimensione, o 1/190
in alta risoluzione) ed è chiuso, ogni spigolo fra due triangoli e ogni faccia rivolta all'esterno,
anche dove i giri entrano l'uno nell'altro; vicino all'apice, dove il giro è più sottile della
parete, è pieno, e ciò che è più piccolo di una cella è tralasciato. Una conchiglia che sta tutta
da una parte della sua ultima apertura, come la valva di un bivalve, è posata su quell'apertura;
ogni altra sta sull'asse di avvolgimento, con l'apice in alto, e la base è un disco in cui affonda
la sua parte più bassa. L'STL non ha unità (gli slicer leggono millimetri), il 3MF dichiara i
millimetri.